Our products
Make your swim spa installation more flexible
Environmental
Operating temperature: 0°C (32°F) to 50°C (122°F)
Storage temperature: -20°C (-4°F) to 85°C (185°F)
Humidity: up to 85% RH, non condensing
Water ingress protection: IPx5
Mechanical
Weight: 4.76 kg (10.5 lbs)
Dimensions (W x H x D):
Chassis: 441.5 x 298.5 x 129 mm (17.38" x 11.75" x 5.1")
Swim Spas UL/CSA electrical specifications
Current Input:
2 x 48 A or 1 x 60 A
Master in.xe
| Output | Voltage | Maximum Current |
| Pump 1 (2 speeds) High | 120/240V | 20 FLA/70 LRA |
| Pump 1 (2 speeds) Low | 120/240V | 15 FLA/60 LRA |
| Pump 2 (1 speed) | 240V | 15 FLA/60 LRA |
| Blower | 120/240V | 6 FLA/10 A |
| Circ. pump | 120/240V | 6 FLA/10 A |
| Direct (audio) | 120/240V | 10 A |
| Light | 12V | 1 A |
| Heater | 240V | 4.0 kW |
**The total maximum amperage for blower, circ pump and Direct cannot exceed 12 Amps
Slave in.xe
| Output | Voltage | Maximum Current |
| Pump 3 (1 speed) | 120/240V | 10 FLA/60 LRA* |
| Pump 4 (1 speed) | 240V | 15 FLA/60 LRA |
| Pump 5 (1 speed) | 120/240V | 10 FLA/60 LRA |
| Light 3 | 120/240V | 6 FLA/10 A |
| Ozone | 120/240V | 6 FLA/10 A |
| Direct (other) | 120/240V | 6 FLA/10 A |
| Light 2 | 12V | 1 A |
| Heater | 240V | 4.0 kW |
*To install pump 5, an in.split cable is required. If the pump 5 is not installed, the pump 3 can be 20 FLA and a two speed pump. If both pump 3 & pump 5 are installed, then each individual pump cannot exceed 10 FLA (max total combined of 20 FLA).
**The total maximum amperage for light 3, Ozone and Direct cannot exceed 12 Amps
heat.wav ratings
| Voltage: | 240 VAC, 60 Hz |
| Current: | 17 A resistive (4 kW at 240V) |
| Flow rate: | Minimum of 18 GPM is required |
UL/CSA Standards
UI 1563 Fifth ed.
CSA No. 22.2-218.1-M89
Swim Spas TUV electrical specifications
Current Input:
3 x 20 A max or 1 x 60 A
Master in.xe
| Output | Voltage | Maximum Current |
| Pump 1 (2 speeds) | 230V | 15 FLA/60 LRA |
| Pump 2 (1 speed) | 230V | 15 FLA/60 LRA |
| Blower | 230V | 6 FLA/10 A |
| Circ. pump | 230V | 6 FLA/10 A |
| Direct (audio) | 230V | 10 A |
| Light | 12V | 1 A |
| Heater | 230V | 3.8 kW |
**The total maximum amperage for blower, circ pump and Direct cannot exceed 12 Amps
Slave in.xe
| Output | Voltage | Maximum Current |
| Pump 3 (1 speed) | 230V | 7.5 FLA/60 LRA* |
| Pump 4 (1 speed) | 230V | 15 FLA/60 LRA |
| Pump 5 (1 speed) | 230V | 7.5 FLA/60 LRA |
| Light 3 | 230V | 6 FLA/10 A |
| Ozone | 230V | 6 FLA/10 A |
| Direct (other) | 230V | 6 FLA/10 A |
| Light 2 | 12V | 1 A |
| Heater | 230V | 3.8 kW |
*To install pump 5, an in.split cable is required. If the pump 5 is not installed, the pump 3 can be 15 FLA and a two speed pump. If both pump 3 & pump 5 are installed, each individual pump cannot exceed 7.5 FLA (max total combined of 15 FLA).
**The total maximum amperage for light 3, Ozone and Direct cannot exceed 12 Amps
heat.wav ratings
| Voltage: | 230 VAC, 50 Hz |
| Current: | 8,7 A resistive (2 kW at 230V) 5,7 A resistive (1.3 kW at 230V) 16 A resistive (3.8 kW at 230V) |
| Flow rate: | Minimum of 18 GPM is required |
TUV Standards
European:
EN/IEC 60335-1: 2002/2001
EN/IEC 60335-2-60: 2003/2002 (incl. Corr. & Am up to 2004)
EN55014-1, EN55014-2
EN61000-3-2, EN61000-3-3
Australia:
AS/NZS 3136:2001 +A1 +A2
AS/NZS 3100:2002 + A1+A2+A3